Saw the sig tango 1x10 slide use difficulty is a 10. Is this in comparison to the other scopes you tested or will this be an issue for fast acquisition in competition shooting?
What are some red dot optic mounts that work for mounting a red dot on top of the LPVO? For me specifically I’m using the 34mm scope switch and I have an Aimpoint Micro P2 footprint red dot.
I'm an idiot and misread the compatible scopes list. I have a vortex Razor HD gen 2 E and need a half size spacer to fit the zoom adjustment ring. Without the spacer, the clamp ring spins on the adjustment, with the skinny spacer, the screws don't reach the other side of the ring. I need something in the middle of this. Do you have any off size spacers for this? WIll they be around any time soon?
I'm not sure how you're an idiot. I've got this exact same problem with the exact same scope (Vortex HD Gen II E 1-6). I don't understand. The compatibility chart reads that this is a staff favorite. Surely, they must have run into this very same issue. If the screws were just a little bit longer, they could engage the threading no problem. The ones they supplied are just out of reach. What gives?
What I was told ( I don’t know for sure) is that the razor gen 2-E and the razor gen 2-HD-E are 2 different scopes and the staff recommended the non-hd version. I went out to Walmart and got this exact tape (Dritz 1" Non-Roll Black Elastic Value Pack, 5 yd.) and replace that ring with it. I’ve got about 1500 rounds on the setup and I love it now. Good luck!
Sorry dude, we haven’t dialed that in yet. If you want us to do that for you, send in an email to Support and tell them to hold it. We will work it out in the next couple days, have our time trials done to figure out what it costs us, and then make a listing for it.
When will the stock be replenished?
Testing, testing, one two three?
How long is the entire system total?
When can we expect them to start shipping out? This wasn’t a preorder, was it?
Also curious about expected shipping time.
Apparently there’s a two week lead time…
Yeah someone else pointed that out to me as well. Total missed that when I read the page.
Saw the sig tango 1x10 slide use difficulty is a 10. Is this in comparison to the other scopes you tested or will this be an issue for fast acquisition in competition shooting?
What is the mount height?
1.93
What are some red dot optic mounts that work for mounting a red dot on top of the LPVO? For me specifically I’m using the 34mm scope switch and I have an Aimpoint Micro P2 footprint red dot.
Well.. for anyone else that has this question, one option I found is the LaRue https://www.larue.com/products/aimpoint-micro-t-1-ring-mount-lt787/
I'm an idiot and misread the compatible scopes list. I have a vortex Razor HD gen 2 E and need a half size spacer to fit the zoom adjustment ring. Without the spacer, the clamp ring spins on the adjustment, with the skinny spacer, the screws don't reach the other side of the ring. I need something in the middle of this. Do you have any off size spacers for this? WIll they be around any time soon?
I'm not sure how you're an idiot. I've got this exact same problem with the exact same scope (Vortex HD Gen II E 1-6). I don't understand. The compatibility chart reads that this is a staff favorite. Surely, they must have run into this very same issue. If the screws were just a little bit longer, they could engage the threading no problem. The ones they supplied are just out of reach. What gives?
What I was told ( I don’t know for sure) is that the razor gen 2-E and the razor gen 2-HD-E are 2 different scopes and the staff recommended the non-hd version. I went out to Walmart and got this exact tape (Dritz 1" Non-Roll Black Elastic Value Pack, 5 yd.) and replace that ring with it. I’ve got about 1500 rounds on the setup and I love it now. Good luck!
I see it says vortex strike eagle 34mm would it also work for the vortex strike eagle 30mm 1-6
so what barrel length is needed to run the scopeswitch, a modlite button, a RAMP ModButton Lite Cage, and a laser?
Are you saying you want to run all of that at 12 o clock?
idealy yes
I watched the install video and saw that an install service is available? Is this available at launch and price point?
Sorry dude, we haven’t dialed that in yet. If you want us to do that for you, send in an email to Support and tell them to hold it. We will work it out in the next couple days, have our time trials done to figure out what it costs us, and then make a listing for it.
Early adopter ready
Will there be a lefty version?
does the wing work with TLR 7 HL SUB
Compatibility issue with SIG’s SP2022 or the streamlight TLR7x?
Does it fit Arken ep8